Configuring FCoE Ports

You can configure FCoE ports by using the fcadm command. Use the fcinfoand fcadm commands to determine the status of FCoE ports. These commands also report the relationship between the Ethernet interface and the FCoE port hosted on that interface.

Other Fibre Channel commands, such as luxadm and cfgadm, report FCoE information, although no distinction is made between FCoE and native FC ports.

How to Create an FCoE Port

Before You Begin

Before you begin this procedure, you must perform the following tasks:

• Enable the 802.3x (also called PAUSE) setting on the Ethernet interface. This setting ensures a lossless Ethernet transport.

• Enable jumbo frames (greater than 2.5 KB) on the Ethernet interface. A Fibre Channel data frame can be as large as 2136 bytes.

  These settings can vary for different Ethernet hardware and drivers. In most cases, you must modify the driver.conf file of the Ethernet interface and then reboot. See the driver.conf file for your Ethernet interface for details on how to enable these features.

  Each virtual port must have a port and node name. The port name must be unique on the SAN. You can assign names manually or use the built-in WWN generator. If you attempt to register duplicate names, the switch will report an error status on the newly registered WWN, and the switch will not register the new WWN. For more information on acceptable name formats, refer to the T11 standard: Fibre Channel Framing and Signaling (FC-FS 2).

  If you try to create an FCoE port on a network interface that does not support FCoE, an error occurs and the FCoE port is not created.

• Enable the following services:

  # svcadm enable svc:/system/fcoe_target:default
  # svcadm enable svc:/system/stmf:default

1. Become an administrator.
2. Create an FCoE port.

   # fcadm create-fcoe-port -i -p Port_WWN -n Node_WWN Ethernet_Interface

   If the selected Ethernet interface does not support Multiple Unicast Address, you are prompted to explicitly enable promiscuous mode on that interface.

   # fcadm create-fcoe-port -i -f Ethernet_Interface

   For example:

   # fcadm create-fcoe-port -i nxge0

How to Delete an FCoE Port

Before You Begin

You can use the fcadm list-fcoe-ports command to display the Ethernet interfaces hosting the FCoE ports.

1. Become an administrator.
2. Delete an FCoE port.

   # fcadm delete-fcoe-port network_interface

   For example:

   # fcadm delete-fcoe-port nxge0

How to Display FCoE Port Status

1. Become an administrator.
2. Display the status of currently configured FCoE ports.

   # fcinfo hba-port -e

   For example:

   # fcinfo hba-port -e
   HBA Port WWN: 200000144fc1f5c8
               Port Mode: Initiator
               Port ID: 9a0042
               OS Device Name: /dev/cfg/c6
               Manufacturer: Sun Microsystems, Inc.
               Model: FCoE Virtual FC HBA
               Firmware Version: N/A
               FCode/BIOS Version: N/A
               Serial Number: N/A
               Driver Name: SunFC FCoEI v20090422-1.00
               Driver Version: v20090422-1.00
               Type: N-port
               State: online
               Supported Speeds: 1Gb 10Gb
               Current Speed: 10 Gb
               Node WWN: 100000144fc1f5c8

   List FC specific information for all FCoE ports in the system.

   # fcadm list-fcoe-ports

   For example:

   # fcadm list-fcoe-ports
   HBA Port WWN: 200000144fc1f5c8
               Port Type: Initiator
               MAC Name: nxge0
               MTU Size: 9194
               Primary MAC Address: 00144fc1f5c8
               Current MAC Address: 0efc009a0042
               Promiscuous Mode: Off

How to Force a FCoE Port Reinitialization

Use the steps below when a FCoE port needs to be reinitialized. You might need to force a FCoE port reinitialization when new devices are added to an FC SAN or because of some misbehaving device on the SAN. In many cases, this operation can resolve problems in an FC-SAN.

When this command issued on the target port side, the target port is reset. When this command is issued from the host port side, the host port is reset.

When an FC switch is connected, other FC ports in the SAN get a remote state change notification (RSCN). Furthermore, other initiators will always rediscover the port after this operation, and the FC login session will be established or reused. This command is disruptive to I/Os, but I/Os continue. This command is not destructive because it does not cause any data loss.

1. Become an administrator.
2. Force a link that is connected to a port to reinitialize.

   For example:

   # fcadm force-lip 200000144fc2d508