format Menu and Command Descriptions

`format` Menu and Command Descriptions

The format menu contents are displayed as follows:

FORMAT MENU:
        disk       - select a disk
        type       - select (define) a disk type
        partition  - select (define) a partition table
        current    - describe the current disk
        format     - format and analyze the disk
        fdisk      - run the fdisk program (x86 only)
        repair     - repair a defective sector
        label      - write label to the disk
        analyze    - surface analysis
        defect     - defect list management
        backup     - search for backup labels
        verify     - read and display labels
        save       - save new disk/partition definitions
        inquiry    - show vendor, product and revision
        volname    - set 8-character volume name
        !<cmd>     - execute <cmd>, then return
        quit
format>

The following table describes the main menu items for the format utility.

Table 13-1 The Main Menu Item Descriptions for the format Utility

Menu Item	Command or Menu?	Description
`disk`	Command	Lists all of the system's drives. Also lets you choose the disk you want to use in subsequent operations. This disk is referred to as the current disk.
`type`	Command	Identifies the manufacturer and model of the current disk. Also displays a list of known drive types. Choose the `Auto configure` option for all SCSI-2 disk drives.
`partition`	Menu	Creates and modifies slices. For more information, see `partition` Menu.
`current`	Command	Displays the following information about the current disk: Device name and device type Number of cylinders, alternate cylinders, heads and sectors Physical device name
`format`	Command	Formats the current disk by using one of these sources of information in this order: Information that is found in the `format.dat` file Information from the automatic configuration process Information that you type at the prompt if no `format.dat` entry exists This command does not apply to IDE disks. IDE disks are preformatted by the manufacturer.
`fdisk`	Menu	x86 platform only: Runs the `fdisk` program to create a Solaris `fdisk` partition. The `fdisk` command cannot be used on disks with an EFI label that are greater than 1 terabyte in size.
`repair`	Command	Repairs a specific block on the current disk.
`label`	Command	Writes a new label to the current disk.
`analyze`	Menu	Runs read, write, and compare tests. For more information, see `analyze` Menu.
`defect`	Menu	Retrieves and displays defect lists. For more information, see `defect` Menu. This feature does not apply to IDE disks. IDE disks manage defects automatically.
`backup`	Command	VTOC – Searches for backup labels. EFI – Not supported.
`verify`	Command	Displays the following information about the current disk: Device name and device type Number of cylinders, alternate cylinders, heads and sectors Partition table
`save`	Command	VTOC – Saves new disk and partition information. EFI – Not applicable.
`inquiry`	Command	SCSI disks only – Displays the vendor, product name, and revision level of the current drive.
`volname`	Command	Labels the disk with a new eight-character volume name that you specify.
`quit`	Command	Exits the `format` menu.

`partition` Menu

The partition menu contents are displayed as follows:

format> partition
PARTITION MENU:
        0      - change `0' partition
        1      - change `1' partition
        2      - change `2' partition
        3      - change `3' partition
        4      - change `4' partition
        5      - change `5' partition
        6      - change `6' partition
        7      - change `7' partition
        select - select a predefined table
        modify - modify a predefined partition table
        name   - name the current table
        print  - display the current table
        label  - write partition map and label to the disk
        quit
partition>

The following table describes the partition menu items.

Table 13-2 Descriptions for partition Menu Items

Subcommand	Description
change ``n' partition`	Enables you to specify the following information for the new partition: Identification tag Permission flags Starting cylinder Size
`select`	Enables you to choose a predefined partition table.
`modify`	Enables you to change all the slices in the partition table. This command is preferred over the individual `change` ``x`' `partition` commands.
`name`	Enables you to specify a name for the current partition table.
`print`	Displays the current partition table.
`label`	Writes the partition map and the label to the current disk.
`quit`	Exits the `partition` menu.

x86: `fdisk` Menu

The fdisk menu is available on x86 based systems only and appears similar to the following.

format> fdisk
            Total disk size is 8924 cylinders
             Cylinder size is 16065 (512 byte) blocks

                                               Cylinders
      Partition   Status    Type          Start   End   Length    %
      =========   ======    ============  =====   ===   ======   ===
          1                 EFI               0  8924    8925    100




SELECT ONE OF THE FOLLOWING:
   1. Create a partition
   2. Specify the active partition
   3. Delete a partition
   4. Change between Solaris and Solaris2 Partition IDs
   5. Edit/View extended partitions
   6. Exit (update disk configuration and exit)
   7. Cancel (exit without updating disk configuration)
Enter Selection:

The following table describes the fdisk menu items.

Table 13-3 x86: Descriptions for fdisk Menu Items

Menu Item	Description
`Create a partition`	Creates an `fdisk` partition. You must create a separate partition for each OS such as Oracle Solaris or DOS. There is a maximum of four partitions per disk. You are prompted for the size of the `fdisk` partition as a percentage of the disk.
`Specify the active partition`	Enables you to specify the partition to be used for booting. This menu item identifies where the first stage boot program looks for the second stage boot program.
`Delete a partition`	Deletes a previously created partition. This command destroys all the data in the partition.
`Change between Solaris and Solaris2 Partition IDs`	Changes partition IDs from 130 (`0x82`) to 191 (`0xbf`) and back again.
`Edit/View extended partitions`	Manages partition information that is generally used for booting.
`Exit (update disk configuration and exit)`	Writes a new version of the partition table and exits the `fdisk` menu.
`Cancel (exit without updating disk configuration)`	Exits the `fdisk` menu without modifying the partition table.

`analyze` Menu

The analyze menu contents are displayed as follows:

format> analyze
 
ANALYZE MENU:
    read     - read only test   (doesn't harm SunOS)
    refresh  - read then write  (doesn't harm data)
    test     - pattern testing  (doesn't harm data)
    write    - write then read      (corrupts data)
    compare  - write, read, compare (corrupts data)
    purge    - write, read, write   (corrupts data)
    verify   - write entire disk, then verify (corrupts data)
    print    - display data buffer
    setup    - set analysis parameters
    config   - show analysis parameters
    quit
analyze>

The following table describes the analyze menu items.

Table 13-4 Descriptions for analyze Menu Items

Subcommand	Description
`read`	Reads each sector on the current disk. Repairs defective blocks as a default.
`refresh`	Reads then writes data on the current disk without harming the data. Repairs defective blocks as a default.
`test`	Writes a set of patterns to the disk without harming the data. Repairs defective blocks as a default.
`write`	Writes a set of patterns to the disk then reads back the data on the disk. Destroys existing data on the disk. Repairs defective blocks as a default.
`compare`	Writes a set of patterns to the disk, reads back the data, and then compares it to the data in the write buffer. Destroys existing data on the disk. Repairs defective blocks as a default.
`purge`	Removes all data from the disk so that the data cannot be retrieved by any means. Data is removed by writing three distinct patterns over the entire disk (or a section of the disk). If the verification passes, a hex-bit pattern is written over the entire disk (or a section of the disk). Repairs defective blocks as a default.
`verify`	In the first pass, writes unique data to each block on the entire disk. In the next pass, reads and verifies the data. Destroys existing data on the disk. Repairs defective blocks as a default.
`print`	Displays the data in the read/write buffer.
`setup`	Enables you to specify the following analysis parameters: Analyze entire disk? yes Starting block number: `depends on drive` Ending block number: `depends on drive` Loop continuously? no Number of passes: 2 Repair defective blocks? yes Stop after first error? no Use random bit patterns? no Number of blocks per transfer: 126 (0/`n`/`nn`) Verify media after formatting? yes Enable extended messages? no Restore defect list? yes Restore disk label? yes
`config`	Displays the current analysis parameters.
`quit`	Exits the `analyze` menu.

`defect` Menu

The defect menu contents are displayed as follows:

format> defect
 
DEFECT MENU:
        primary  - extract manufacturer's defect list
        grown    - extract manufacturer's and repaired defects lists
        both     - extract both primary and grown defects lists
        print    - display working list
        dump     - dump working list to file
        quit
defect>

The following table describes the defect menu items.

Table 13-5 The defect Menu Item Descriptions

Subcommand	Description
`primary`	Reads the manufacturer's defect list from the disk drive and updates the in-memory defect list.
`grown`	Reads the grown defect list and then updates the in-memory defect list. Grown defects are defects that have been detected during analysis.
`both`	Reads both the manufacturer's defect list and the grown defect list. Then, updates the in-memory defect list.
`print`	Displays the in-memory defect list.
`dump`	Saves the in-memory defect list to a file.
`quit`	Exits the `defect` menu.

Skip Navigation Links
Exit Print View
	Oracle Solaris 11.1 Administration: Devices and File Systems Oracle Solaris 11.1 Information Library

partition Menu

x86: fdisk Menu

analyze Menu

defect Menu

`format` Menu and Command Descriptions

`partition` Menu

x86: `fdisk` Menu

`analyze` Menu

`defect` Menu